A roof is not a covering laid on a building; it is a system of pitch, overlap, drainage, ventilation and structure. Get those right and almost any local material will keep you dry. Get them wrong and the best shingles in the forest will leak within a season.
The roof is a system
Water must run off, not sit or blow in. That means enough pitch for the covering, enough overlap so water never finds a joint, and enough eaves overhang to throw water clear of the walls. It also means the back of the covering must be able to dry. A roof that is sealed tight on the underside traps moisture from below and rots from the inside.
In a hand-built roof, use spaced boards or purlins rather than a solid sealed deck. Leave gaps for air movement, and keep the underside open to a ventilated loft. Do not stuff insulation directly against the back of shingles or thatch; leave an air path. In cold climates, separate the warm ceiling from the cold roof with an insulated, airtight layer, and ventilate the cold side.
| Covering | Minimum pitch | Approximate weight | Typical life |
|---|---|---|---|
| Wood shingles | 25–35° (steeper in exposed sites) | 15–25 kg/m² | 20–50 years |
| Water reed thatch | 45–50° | 25–40 kg/m² | 25–50 years |
| Straw thatch | 45–50° | 25–35 kg/m² | 10–25 years |
| Clay plain tiles | 40–45° | 45–65 kg/m² | 50–100 years |
| Clay pantiles | 30–35° | 35–50 kg/m² | 50–100 years |
| Stone slates | 45–50° | 60–120 kg/m² | 100+ years |
Ask an engineer about the structure. A roof carries its own weight plus wind, snow and the people who built it. The table is for early planning, not for sizing rafters. Local timber species, spans, snow load and wind exposure decide the dimensions.
Riven wooden shingles
Shingles are thin, tapered pieces of wood laid in overlapping courses. Riven shingles follow the grain and are far more durable than sawn ones because the fibres run continuously through the piece. The best species are naturally rot-resistant: western red cedar, oak, sweet chestnut, larch, cypress and some pines. Use straight, clear logs with no large knots; a knot is a crack waiting to happen.
Cut logs into billets a little longer than the finished shingle — commonly 40–60 cm. Split the billet into quarters or eighths with wedges and a mallet, then rive thin pieces with a froe, a blade with a handle at right angles. A shingle horse holds the billet while you work. Trim the edges with a drawknife or axe to a taper: thicker at the butt, thinner at the top. The finished shingle is typically 10–25 cm wide and 1–2 cm thick.
Lay from the eaves up, in courses that overlap by at least two-thirds of the shingle length. The exposed “weather” of each course is usually 15–25 cm. Stagger the joints so no vertical gap lines up with the one below. Fix each shingle with two corrosion-resistant nails placed about 2–3 cm above the butt edge and 2–3 cm in from the sides, so the next course covers the nail heads. Do not drive nails tight enough to split the wood; leave the shingle free to move slightly.
Use a double starter course at the eaves, and a ridge cap of bent shingles, boards or metal if available. At valleys and chimneys, use flashing or a generous overlap of lead, copper or tarred cloth — whatever you can source — and keep the detail simple enough to inspect and repair.
Thatch
Thatch is a thick, layered coat of reed or straw that sheds water by steep pitch and deep overlap. Water reed (Phragmites australis) is the most durable material; long wheat straw is traditional but shorter-lived and more attractive to vermin. Harvest dry, store dry, and never use mouldy material.
Bundles are laid in overlapping courses, each fixed to the battens with hazel spars or tarred twine, and the surface is beaten and combed into a smooth, dense face. A new thatch is typically 30–40 cm thick, with a ridge that is built up and capped. The pitch should be 45–50°; a shallow thatch is a leaking thatch. Eaves need deep overhang and a wire mesh or netting to keep birds out.
Thatch is heavy and needs a strong roof structure. It is also a fire risk: keep chimneys well insulated, fit a spark arrestor, and maintain clearances. It can be repaired by patching or by re-ridging, and a well-built reed roof may last 25–50 years. Learn from a working thatcher before attempting a whole roof; the craft is in the surface tension and the fixings, not just the bundles.
Clay and stone tiles
Fired clay tiles are laid in double-lap courses: each tile overlaps the two below. Plain tiles need a steep pitch (40–45°) because each tile is small and the joints are many. Pantiles, with their curved profile, interlock side by side and can go down to about 30–35°. Stone slates are heavier and need a steeper pitch; they are hung on timber battens and often graduated in size, larger at the eaves.
Tiles are hung on battens or nailed, depending on the design. In windy sites, every tile may need fixing; in sheltered sites, only every third course. Do not rely on gravity alone for a roof that will see storms. Use corrosion-resistant fixings, and keep the battens ventilated.
Clay tiles are brittle: do not walk on them, and store them on edge. A tile roof is quiet, fireproof and long-lived, but it is also heavy. Check the structure before you commit.
Structure and detailing
A simple coupled roof has rafters rising to a ridge board, tied across at the wall plate. Purlins run under the rafters to shorten their span. The roof must be tied down, not just rested on the walls: use metal straps, timber pegs or a ring beam, and brace the structure against wind. Keep the load path continuous from ridge to foundation.
Overhangs protect the walls. Aim for at least 30–45 cm, and more on the weather side; a deep eaves also shades summer sun and keeps rain off the plinth. Gutters and downpipes are optional but valuable: they keep water away from the foot of an earth wall. A simple gutter can be a hollowed log or a folded sheet of metal; a downpipe can be a fired clay pipe.
Ventilate the roof space. Air must enter at the eaves and leave at the ridge or a high vent. This carries away moisture from the rooms below and dries the back of the covering. In a thatched roof, ventilation also discourages condensation and rot.
Troubleshooting
| Symptom | Likely cause | Fix |
|---|---|---|
| Leak near the eaves | Insufficient overhang or blocked gutter | Extend the overhang, clear the gutter, add a drip edge |
| Leak around chimney | Failed flashing or no cricket | Rebuild flashing with a saddle; keep a gap for movement |
| Moss and rot on shingles | Shade, wetting, no ventilation | Prune shade, improve airflow, replace rotten shingles |
| Thatch sagging | Weak battens or wet straw | Re-fix spars, replace the wet section, check the structure |
| Tiles sliding | Missing fixings or too shallow a pitch | Re-fix, add battens, or change covering; do not walk on old tiles |
Safety
Falls are the biggest risk. Work with at least one other person, use a proper ladder and scaffold, tie off where possible, and never work on a wet or windy roof. Tools. A froe and axe can take fingers; keep a clear striking zone and wear eye protection. Fire. Thatch and dry shingles ignite easily: keep chimneys clean, fit spark arrestors and maintain clearances. Structure. Get an engineer to check any roof you will live under, especially a heavy tile or stone roof.
Sources and further reading
- Wikipedia: Wood shingle — riving, species and installation.
- Wikipedia: Thatching — materials, methods and regional traditions.
- Wikipedia: Roof tiles — clay, stone and concrete tile types.
- Wikipedia: Froe — the tool for riving shingles and laths.